BuildMyMTB
Prototype - Evolving Daily

Industry Nine Hydra Classic rear hub Rear Hub

Every verified variant of this model carries a lifecycle status.

What the checker says126will not fit

Run variant by variant through the mountain bike builder’s own engine. Every sentence below is the checker’s, unedited. Nothing here says this part fits your bike; it says what it does and does not fit among the parts we hold.

Checked against 6050 verified mountain bike parts in this catalog. 5925 produced no finding of any kind; that is Hydra Classic rear hub (Shimano HG). Hydra Classic rear hub (Center Lock, Micro Spline) clears 5861. Each variant produces 35 to 52 distinct errors and 0 distinct warnings.

Will not fit

  • Will not fiterror · Rear RotorRear rotor: a 6-bolt rotor does not mount on a Center Lock rear hub as it is - the two use different rotor interfaces. The part that bridges them is a Center Lock adapter, and the ones makers publish fit one-piece rotors only. A shim or adapter may make other sizes or standards work, but that is a modification, not a fit. On 112 of the 177 verified rotors in this catalog. Applies to 3 of 6 variants.
  • Will not fiterror · Rear RotorRear rotor interface mismatch: Center Lock rotor on 6-bolt rear hub - no adapter exists for this direction. On 65 of the 177 verified rotors in this catalog. Applies to 3 of 6 variants.
  • Will not fiterror · FrameRear axle mismatch: Frame is SuperBoost 157x12 but Rear wheel hub is Boost 148x12. On 21 of the 258 verified frames in this catalog. Applies to all 6 variants.
  • Will not fiterror · FrameRear axle mismatch: Frame is 135x5-qr but Rear wheel hub is Boost 148x12. On 5 of the 258 verified frames in this catalog. Applies to all 6 variants.
  • Will not fiterror · FrameRear axle mismatch: Frame is 10x135 bolt-on but Rear wheel hub is Boost 148x12. On 2 of the 258 verified frames in this catalog. Applies to all 6 variants.
  • Will not fiterror · FrameRear axle mismatch: Frame is 150x12 (DH, pre-Boost) but Rear wheel hub is Boost 148x12. On 2 of the 258 verified frames in this catalog. Applies to all 6 variants.

Freehub, Cassette. 120 more findings from the same check, on up to 1 of the 60 verified cassettes each.

Open a variant in the builder to see the ones that apply to your own parts.

The checker compares the dimensions listed in what we check, and what we don’t. “No conflicts found” means no conflict among those dimensions — not a guarantee that a build works. Errors mean it won’t fit; warnings mean it works but check; infos are notes.

$460.00 MSRP·265 to 286 g

What the maker states

Freehub
/ driver Shimano HG (on 2 of 6 variants); / driver Shimano Micro Spline (on 2 of 6 variants); / driver SRAM XD (on 2 of 6 variants)
Rotor mount
Center Lock (on 3 of 6 variants); 6-bolt (on 3 of 6 variants)
Hub
Spacing Boost 148x12

A value shown as a set or a range differs between this model’s variants and is never one variant’s spec.

6 verified variants

VariantFreehubRotor mountPrice (MSRP)WeightSourceLast checkedBuild
Hydra Classic rear hub (Micro Spline)/ driver Shimano Micro Spline6-bolt$460.00286 gmaker’s page2026-09-03Build with this
Hydra Classic rear hub (XD)/ driver SRAM XD6-bolt$460.00286 gmaker’s page2026-09-03Build with this
Hydra Classic rear hub (Shimano HG)/ driver Shimano HG6-bolt$460.00286 gmaker’s page2026-09-03Build with this
Hydra Classic rear hub (Center Lock, Micro Spline)/ driver Shimano Micro SplineCenter Lock$460.00265 gmaker’s page2026-09-03Build with this
Hydra Classic rear hub (Center Lock, XD)/ driver SRAM XDCenter Lock$460.00265 gmaker’s page2026-09-03Build with this
Hydra Classic rear hub (Center Lock, Shimano HG)/ driver Shimano HGCenter Lock$460.00265 gmaker’s page2026-09-03Build with this
The rest of what the maker states1 not published

1 further field the checker looks for is not published by Industry Nine, so we leave it blank rather than estimate it, and that check stays silent on this rear hub. It is maximum system weight. Each is recorded as “not stated by the maker (not checked)”.

Source: each variant links the maker’s own page in the table above. Last checked 2026-09-03.

Checked against

The checker ran this model against every verified part below that it has a slot for, the same way it checks a build in the builder. What follows is the verdict it actually produced for that specific pairing — not a recommendation, and not a guarantee any of these parts fits your own bike.

6 of 1879 counterparts with a page of their own that the checker actually probed this model against, in alphabetical order by brand and model — never by price, popularity or the verdict itself.

Where this sits

Previous: Industry Nine 1/1 rear hubNext: Industry Nine Hydra2 rear hubAll Industry Nine rear hubsOpen a variant in the builder to see the ones that apply to your own parts