BuildMyMTB
Prototype - Evolving Daily

Industry Nine 1/1 front hub (Boost Front Hub

What the checker says7will not fit

Run variant by variant through the mountain bike builder’s own engine. Every sentence below is the checker’s, unedited. Nothing here says this part fits your bike; it says what it does and does not fit among the parts we hold.

Checked against 6134 verified mountain bike parts in this catalog. 5989 produced no finding of any kind; that is 1/1 front hub (Boost 15x110). 1/1 front hub (Boost 15x110, Center Lock) clears 5942. Each variant produces 6 distinct errors and 0 distinct warnings.

Will not fit

  • Will not fiterror · Front RotorFront rotor: a 6-bolt rotor does not mount on a Center Lock front hub as it is - the two use different rotor interfaces. The part that bridges them is a Center Lock adapter, and the ones makers publish fit one-piece rotors only. A shim or adapter may make other sizes or standards work, but that is a modification, not a fit. On 112 of the 177 verified rotors in this catalog. Applies to 1 of 2 variants.
  • Will not fiterror · Front RotorFront rotor interface mismatch: Center Lock rotor on 6-bolt front hub - no adapter exists for this direction. On 65 of the 177 verified rotors in this catalog. Applies to 1 of 2 variants.
  • Will not fiterror · ForkFront axle mismatch: Fork is 20x110 Boost (DH) but Front wheel hub is Boost 15x110. On 56 of the 490 verified forks in this catalog. Applies to all 2 variants.
  • Will not fiterror · ForkFront axle mismatch: Fork is 15x100 (non-Boost) but Front wheel hub is Boost 15x110. On 14 of the 490 verified forks in this catalog. Applies to all 2 variants.
  • Will not fiterror · ForkFront axle mismatch: Fork is 9x100-qr but Front wheel hub is Boost 15x110. On 7 of the 490 verified forks in this catalog. Applies to all 2 variants.
  • Will not fiterror · ForkFront axle mismatch: Fork is 20x110 standard (DH, non-Boost) but Front wheel hub is Boost 15x110. On 2 of the 490 verified forks in this catalog. Applies to all 2 variants.
  • Will not fiterror · ForkFront axle mismatch: Fork is Cannondale Lefty 60 but Front wheel hub is Boost 15x110. On 1 of the 490 verified forks in this catalog. Applies to all 2 variants.
The checker compares the dimensions listed in what we check, and what we don’t. “No conflicts found” means no conflict among those dimensions — not a guarantee that a build works. Errors mean it won’t fit; warnings mean it works but check; infos are notes.

$150.00 MSRP·137 to 165 g

What the maker states

Rotor mount
Center Lock (on 1 of 2 variants); 6-bolt (on 1 of 2 variants)
Hub
Spacing Boost 15x110

A value shown as a set or a range differs between this model’s variants and is never one variant’s spec.

2 verified variants

VariantRotor mountPrice (MSRP)WeightSourceLast checkedBuild
1/1 front hub (Boost 15x110)6-bolt$150.00165 gmaker’s page2026-09-03Build with this
1/1 front hub (Boost 15x110, Center Lock)Center Lock$150.00137 gmaker’s page2026-09-03Build with this
The rest of what the maker states1 not published

1 further field the checker looks for is not published by Industry Nine, so we leave it blank rather than estimate it, and that check stays silent on this front hub. It is maximum system weight. Each is recorded as “not stated by the maker (not checked)”.

Source: each variant links the maker’s own page in the table above. Last checked 2026-09-03.

Checked against

The checker ran this model against every verified part below that it has a slot for, the same way it checks a build in the builder. What follows is the verdict it actually produced for that specific pairing — not a recommendation, and not a guarantee any of these parts fits your own bike.

6 of 1885 counterparts with a page of their own that the checker actually probed this model against, in alphabetical order by brand and model — never by price, popularity or the verdict itself.

Where this sits

Industry Nine 1/1 front hub (Boost is the first model on that list.Next: Industry Nine Hydra Classic front hubAll Industry Nine front hubsOpen a variant in the builder to see the ones that apply to your own parts